|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
|
127 registered members (Shaneomac2, Jdkprp70, 270wsm, ImThere, BentBarrel, MoeBuck, GomerPyle, centralala, oakachoy, foldemup, Lightfoot, DEDTRKY, gregnbc, crenshawco, bama_earl, Scout308, hyco, cartervj, Remington270, JA, somedude, Fishduck, alhawk, JBrown1975, sloughfoot, CeeHawk37, Okatuppa, CAL, BPI, Floorman1, RidgeRanger, AU7MM08, 3Gs, Antelope08, IDOT, FreeStateHunter, TexasHuntress, burbank, dawgdr, Tree Dweller, JAM, slippinlipjr, Luxfisher, mdavis, Heath, thayerp81, JDW25, mossyback, Andalusia, bamapanic, Kicker, Longtine, globe, buck_buster, Dixiepatriot, BamaBoHunter, trlrdrdave, rickyh_2, clayk, Buckwheat, Backwater, WEMOhunter, TCG5, Beer Belly, Whitebone, NWFJ, Jwillbucks, Powers, Ryano, Skullworks, PaytonWP, JKlep, Moose24, skoor, effinacotton, Droptine-13, DryFire, straycat, Cuz-Pat, ParrotHead89, 000buck, dagwood, MurphySimmons, SEWoodsWhitetail, deadeye48, LIOJeff, BD, jacannon, Jmfire722, outdoorguy88, catdoctor, CKyleC, TDog93, XVIII, GobbleGrunt, odocoileus, turkey247, Pocosin, Huntn2feed5, AUtgr, stl32, gman, TurkeyJoe, bodock, UARandy3, ducky25, PossumPecker, dquick1, jmj120, gastoka, AL18, NVM1031, BACK40, toothdoc, Morgan, Ben Downs, 11 invisible),
1,011
guests, and 0
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Re: Wheel bearings
[Re: FurFlyin]
#2557113
08/20/18 08:26 PM
08/20/18 08:26 PM
|
Joined: Jun 2016
Posts: 5,509
Luverne
tbest3
12 point
|
12 point
Joined: Jun 2016
Posts: 5,509
Luverne
|
New hubs at the parts store aren't terribly expensive if you have to go that route. No, they aren't that expensive. They also sell them at Tractor Supply. I can get them a WHOLE lot cheaper than a parts store, but he's in Luverne and shipping would eat up the savings. I wrote, beat the crap out of them and buy new ones to replace with. I meant, buy new bearings and races. I have not met a hub yet that I couldn't get the races out of. If you have to you can weld around the inside of the race. That will shrink the steel and make it easier to get out. I'd use that as a last resort. I've cut no telling how many bearings off spindles or shafts that had been "forge" welded in place. That's easier than getting bad races out of hubs. tbest, if you decided to buy a new hub, keep the old one and I want it. I want to see if I can get them out. It may take a while to get the aldeer express to get it from Luverne to Albertville, but I want a shot at it. LOL My daddy came by earlier, he’s gonna take it to the mechanic shop at work tomorrow. I’m probably gonna go ahead with new hubs anyway. Like y’all said, they ain’t that expensive. If he can’t get them out tomorrow we’ll find a way to get it to you though.
|
|
|
|
