|
|
|
|
|
|
|
|
Trade
by AustinC. 04/26/24 07:31 PM
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
|
28
|
29
|
30
|
|
|
|
|
|
|
43 registered members (PikeRoadHunter, coonhunterrn, SC53, mopar, CatfishJunkie, Driveby, Drycreek, BD, DEADorALIVE, Flatwoods, Nightwatchman, bamaeyedoc, Tree Dweller, Shane99, Irishguy, Geeb, jhardy, Mbrock, fur_n_feathers, Chaser357, COOTER, Cactus_buck, coldtrail, Raspy, sawdust, BamaBoHunter, JA, MarksOutdoors, jsubrett6, mossyback, turfarmer, Swamp Monkey, knock him down, Flyliner, 000buck, roll_tide_hunts, Ron A., Ruger7mag, BearBranch, Alb, bradbathome, Gobble4me757, 1 invisible),
1,155
guests, and 0
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Precise powder measuring!!
#4061341
01/14/24 11:20 PM
01/14/24 11:20 PM
|
Joined: Dec 2009
Posts: 9,051
USA
marshmud991
OP
14 point
|
OP
14 point
Joined: Dec 2009
Posts: 9,051
USA
|
I pulled the bullets out of 60 rounds of 6.5 Grendel PPU ammo. I poured the powder from the first 20rounds on my digital powder scale and 18 of them weighed 29.3 grains. One was 29.2 and the other was 29.4. I the randomly weighed rounds out of the other 40 and everyone weighed 29.3. I’d say that is pretty precise measurements for a cheaper factory load.
It's hard to kiss the lips at night that chews your a$$ all day long.
|
|
|
Re: Precise powder measuring!!
[Re: marshmud991]
#4061366
01/15/24 12:13 AM
01/15/24 12:13 AM
|
Joined: Sep 2012
Posts: 18,051
North AL
AU338MAG
Old Mossy Horns
|
Old Mossy Horns
Joined: Sep 2012
Posts: 18,051
North AL
|
I assume the ammo was loaded with ball powder. Ball is much easier to get close using a volumetric type measure than extruded. I don't use my Chargemaster for ball powders, just an old RCBS uniflow and it's always within 0.1 grain when I spot check charges with scales.
Dying ain't much of a living boy...Josey Wales
Molon Labe
|
|
|
Re: Precise powder measuring!!
[Re: AU338MAG]
#4061394
01/15/24 06:17 AM
01/15/24 06:17 AM
|
Joined: Dec 2009
Posts: 9,051
USA
marshmud991
OP
14 point
|
OP
14 point
Joined: Dec 2009
Posts: 9,051
USA
|
I assume the ammo was loaded with ball powder. Ball is much easier to get close using a volumetric type measure than extruded. I don't use my Chargemaster for ball powders, just an old RCBS uniflow and it's always within 0.1 grain when I spot check charges with scales. Yes Sir. It looked like a small ball powder. I’m very new to this. I just thought that was pretty good.
It's hard to kiss the lips at night that chews your a$$ all day long.
|
|
|
Re: Precise powder measuring!!
[Re: marshmud991]
#4061409
01/15/24 07:11 AM
01/15/24 07:11 AM
|
Joined: Dec 2016
Posts: 10,407
northport
deadeye48
Booner
|
Booner
Joined: Dec 2016
Posts: 10,407
northport
|
That is very good for factory stuff
When I need expert advice I tend to talk to myself
The older I get the better I used to be
|
|
|
|
