|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
88 registered members (BCLC, TamaDrumhead, beetrapper, Antelope08, Luxfisher, jake5050, hunterturf, Ant67, BrandonClark, 10mm, chill, Downwind, Gunpowder, Mansfield, fillmore, JustHunt, !shiloh!, Cynical, HURRICANE, Peach, Chaser357, MS_Hunter, icducks, sanderson, Ben2, XVIII, aucivil, Hunting15, aucountry, BPI, Chancetribe, Overland, Turkeyneck78, HoofNSpur, 000buck, Bustinbeards, coldtrail, dawgdr, turfarmer, Morris, Remington270, Hoytdad10, 3006bullet, BobK, Scooter7, Mbrock, Rebelhunter_21, Canterberry, Gunner211, goodman_hunter, Aldecks1, GrandSlam, hippi, BamaRick, MikeP, Bruno, weatherby, CNC, brett.smith, Frogeye, JoeBuck, SC53, BuckRidge17, AU coonhunter, RCHRR, BhamFred, CCC, mcninja, Smitty4Bama, jarcher38, KnightRyder, 7x57_Mauser, crenshawco, bholmes, ridgestalker, MGrubber, Buckwheat, Turkey, 10 invisible),
918
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Elite Ritual 33
#2775504
04/01/19 07:08 PM
04/01/19 07:08 PM
|
Joined: Dec 2010
Posts: 4,545 Centreville AL.
sbo1971
OP
10 point
|
OP
10 point
Joined: Dec 2010
Posts: 4,545
Centreville AL.
|
I have a PSE Decree IC and a Hoyt Defiant 30, both of which I have paper tuned very quickly, and easily. Picked up and Elite Ritual 33 and the only way I could get a bullet hole paper tune was to move the linear tunable roller all the way to the right and the QAD rest all the way to the left. Of course when I did this I was unable to sight in at 2o yds. Read everything I could on here about this with no luck so I took it to the shop. He was able to get it paper tuned to him but I’m still getting a point left nock right and nock low tear. The best I can get it is about an inch tear to the right and half an inch high high. I get this wether I use a thumb release or hinge. I’m shooting Easton FMJ’s 300 spine 30” in length with a 100 grain point. I tried purposely torquing my bow hand but with very little results. If it were the bow I would think that the man at the shop wouldn’t have been able to paper tune it so what am I doing wrong?
I noticed on the draw board that the top cam leans where as the bottom cam has little to no lean during the draw cycle, the top of the cam leans to the left or towards the riser pretty signicantly
Elite Omnia, Easton FMJ, Axcel Landslyde 5 pin slider.
|
|
|
Re: Elite Ritual 33
[Re: sbo1971]
#2799719
05/03/19 08:18 PM
05/03/19 08:18 PM
|
Joined: May 2018
Posts: 3,257 Hoover,Al. StateChamps
Big Bore
10 point
|
10 point
Joined: May 2018
Posts: 3,257
Hoover,Al. StateChamps
|
You may have to put it in a bow press and change the string twist ratio. It is very easy to do but if you haven't done it before, you need to watch an expert do it. Take it to where you bought it.
Hunting brings out the worst in people.
|
|
|
|