Velvet
by Mbrock. 04/28/24 09:16 PM
|
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
84 registered members (Peach, YellaLineHunter, tmhrmh1, Kelly_123, fur_n_feathers, BatesConst, BrentsFX4, 4Tigers, NotsoBright, brokefixer, Hoytdad10, Bread, coldtrail, MS_Hunter, Geeb, Lung_buster, Safetyman, CatHeadBiscuit, SouthBamaSlayer, 10 POINT, GUT_SHOT, booner, CKyleC, UA Hunter, crenshawco, courseup, hamma, Joe4majors, KnightRyder, CCC, 7x57_Mauser, rrice0725, 700ltr308, TEM, goodman_hunter, Big AL 76, Jweeks, M48scout, Mansfield, Chaser357, dsmc, 2walnuts, JPFlier, Ol Backwoods Boy, sidehitter, Lonster, Skullworks, 000buck, hippi, dawgdr, mossyback, cullbuck, quickshot, fireman176, SuperSpike, specialk, JLMiller, roll_tide_hunts, bambam32, JohnG, wareagul, Ben2, just_an_illusion, Hunting-231, HappyHunter, ParrotHead89, blade, Flyliner, DoubleShoalsJR, leroycnbucks, bamaeyedoc, csg1994, snakebit, deadeye48, AU338MAG, outdoorguy88, 8 invisible),
822
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Resize fix
#2124522
05/28/17 01:32 PM
05/28/17 01:32 PM
|
Joined: Apr 2013
Posts: 4,329 Northeast Florida
BamaGrad85
OP
10 point
|
OP
10 point
Joined: Apr 2013
Posts: 4,329
Northeast Florida
|
I was resizing brass earlier and as I was pulling a shell the resizer came apart. I was using resize lube so I was a bit surprised that it happened. I got the part stuck in the brass out at the expense of using a dremel grinder on the brass to get it free. I think I know how to put resizer together but not sure if it will hold. Does any one know what I need to do next or just buy a new die set?
I came, I saw, so I killed them all......Vern
|
|
|
Re: Resize fix
[Re: odocoileus]
#2128566
06/02/17 04:18 PM
06/02/17 04:18 PM
|
Joined: Apr 2013
Posts: 4,329 Northeast Florida
BamaGrad85
OP
10 point
|
OP
10 point
Joined: Apr 2013
Posts: 4,329
Northeast Florida
|
I assume it is one of the collet dies. If I understand correctly, the case is out but the sizing rod is stuck in the case? Not anymore. I used my Dremel grinder and removed the sizing rod from the case. I put it back in the collet and tightened the screw as tight as I could and finished resizing 38 more cases. It held just fine. I now have 59 cases cleaned, resized, primed and ready to load powder & bullets.
I came, I saw, so I killed them all......Vern
|
|
|
|