Velvet
by Mbrock. 04/28/24 09:16 PM
|
|
|
|
|
|
|
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
|
28
|
29
|
30
|
|
|
|
|
|
|
49 registered members (4Tigers, MountainTopHunter, FreeStateHunter, desertdog, Ten37, jawbone, gradythemachine, TexasHuntress, MC21, hunterturf, Cactus_buck, Whild_Bill, FastXD, Longtine, hue, ShaftOne, sappsman, Jotjackson, hillmp, Jmkiper, rwh1, 3blades, trlrdrdave, quickshot, BCLC, CatHeadBiscuit, UARandy3, jaydub12, jake5050, Uokman2014, AU coonhunter, laylandad, Turkeyneck78, 380jeff, Blackwater_Reb, Joe4majors, Moose24, AU338MAG, BamaFan64, Hester, RCHRR, 007, Captain Howdy, robinhedd, Gut Pile 32, 4 invisible),
806
guests, and 0
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Re: Anybody loading for 6.5 Creedmoor
[Re: Standbanger]
#2041090
02/27/17 11:32 AM
02/27/17 11:32 AM
|
Joined: Dec 2016
Posts: 10,410
northport
deadeye48
Booner
|
Booner
Joined: Dec 2016
Posts: 10,410
northport
|
Using Nosler brass, CCI primers and the Hornady 143gn ELDX being pushed by 39.5 gns of H4350
Will shoot one ragged hole 5 shot groups from a custom build I finished in November of last year
When I need expert advice I tend to talk to myself
The older I get the better I used to be
|
|
|
Re: Anybody loading for 6.5 Creedmoor
[Re: Standbanger]
#2042336
02/28/17 11:36 AM
02/28/17 11:36 AM
|
Joined: Jun 2016
Posts: 3,142
alabama northport
birdcarver
10 point
|
10 point
Joined: Jun 2016
Posts: 3,142
alabama northport
|
51.3 gn Imr 4150 3 shot group in quarter at 110 yds using once fired 243 brass and necked to 6.5 creedmoor
Last edited by birdcarver; 02/28/17 11:37 AM.
|
|
|
Re: Anybody loading for 6.5 Creedmoor
[Re: deadeye48]
#2043463
03/01/17 07:17 AM
03/01/17 07:17 AM
|
Joined: Nov 2014
Posts: 58
North AL
Mike_W
spike
|
spike
Joined: Nov 2014
Posts: 58
North AL
|
Using Nosler brass, CCI primers and the Hornady 143gn ELDX being pushed by 39.5 gns of H4350
Will shoot one ragged hole 5 shot groups from a custom build I finished in November of last year 39.5 gr H4350 behind the 143 ELD-X is a good place to start, but you're likely going to find better nodes up between 41-43 gr in terms of velocity, SD, and ES. I run 41.8 gr H4350 under 143 ELD-X using Hornady brass that I anneal after each firing, using a CCI 200 primer. Under half-MOA out past 800 yards...
|
|
|
Re: Anybody loading for 6.5 Creedmoor
[Re: Mike_W]
#2045979
03/03/17 12:38 PM
03/03/17 12:38 PM
|
Joined: Dec 2016
Posts: 10,410
northport
deadeye48
Booner
|
Booner
Joined: Dec 2016
Posts: 10,410
northport
|
Already tried those areas on the load scale and it just wouldn't shoot 39.5 was the sweet spot Using Nosler brass, CCI primers and the Hornady 143gn ELDX being pushed by 39.5 gns of H4350
Will shoot one ragged hole 5 shot groups from a custom build I finished in November of last year 39.5 gr H4350 behind the 143 ELD-X is a good place to start, but you're likely going to find better nodes up between 41-43 gr in terms of velocity, SD, and ES. I run 41.8 gr H4350 under 143 ELD-X using Hornady brass that I anneal after each firing, using a CCI 200 primer. Under half-MOA out past 800 yards...
When I need expert advice I tend to talk to myself
The older I get the better I used to be
|
|
|
Re: Anybody loading for 6.5 Creedmoor
[Re: deadeye48]
#2047461
03/05/17 03:14 AM
03/05/17 03:14 AM
|
Joined: Nov 2014
Posts: 58
North AL
Mike_W
spike
|
spike
Joined: Nov 2014
Posts: 58
North AL
|
Already tried those areas on the load scale and it just wouldn't shoot 39.5 was the sweet spot Using Nosler brass, CCI primers and the Hornady 143gn ELDX being pushed by 39.5 gns of H4350
Will shoot one ragged hole 5 shot groups from a custom build I finished in November of last year 39.5 gr H4350 behind the 143 ELD-X is a good place to start, but you're likely going to find better nodes up between 41-43 gr in terms of velocity, SD, and ES. I run 41.8 gr H4350 under 143 ELD-X using Hornady brass that I anneal after each firing, using a CCI 200 primer. Under half-MOA out past 800 yards... Interesting
|
|
|
|
