|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
119 registered members (AU338MAG, mw2015, Stu, M48scout, RCHRR, limabean, dtmwtp, sj22, gregnbc, turkey247, Skillet, Bulls eye, abolt300, Reptar, globe, BearBranch, slickwilly, BCLC, twaldrop4, PaytonWP, Teacher One, Bronco 74, HSV. HUNTER, CNC, Beer Belly, dirtwrk, Turberville, chevydude2015, .308, Turkeyhunter12, mcninja, DoeNut, CarbonClimber1, aubigmac, dsmc, gman, BAR1225, slanddeerhunter, DryFire, jawbone, Ridgehunter36, 3Gs, jwalker77, Woodsy, coosabuckhunter, BamaBoHunter, odocoileus, Standbanger, JKlep, crenshawco, booner, coldtrail, Overland, Showout, Gobble4me757, RSF, Gut Pile 32, desertdog, Fishduck, AL18, ALFisher, AJones, Young20, doublefistful, zwick, MTeague, okfuski, joe sixpack, BD, Bandit635, Shaneomac2, PapaD, PikeRoadHunter, foldemup, Turkeyneck78, Ron A., 7PTSPREAD, Big AL 76, deerhunter_1, Okatuppa, biglmbass, MS_Hunter, Morris, Paint Rock 00, AU7MM08, Cdub, Ridge Life, dave260rem!, JohnG, BCD, canvasback, ImThere, GomerPyle, somedude, sfortney32, Nightwatchman, Andalusia, coonhunterrn, MGrubber, Chancetribe, auman, SC53, Buck-bomb, slim68, snakebit, Driveby, JBrown1975, Recovered, 11 invisible),
1,483
guests, and 0
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: KHOOKS]
#3573170
01/05/22 02:27 PM
01/05/22 02:27 PM
|
Joined: Jun 2019
Posts: 3,409 Sylvania Alabama
Sandmtnslayer
10 point
|
10 point
Joined: Jun 2019
Posts: 3,409
Sylvania Alabama
|
Does the thickness of the powder coating come in to play with the overall diameter of the bullet? I'm asking do the mold have to be special or smaller to allow for the powder coating? I was thinking the very same thing
Not all Indians were hunters some toted firewood
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: Sipseyhunter]
#3573281
01/05/22 04:42 PM
01/05/22 04:42 PM
|
Joined: Jun 2016
Posts: 3,142 alabama northport
birdcarver
OP
10 point
|
OP
10 point
Joined: Jun 2016
Posts: 3,142
alabama northport
|
Those look good. What method are you using to coat? What brand powder? I use Eastwood HOT COAT [POWDER COATING POWDER] buy it by the pound a pound will coat few thousand, was 9.00 pound
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: birdcarver]
#3573496
01/05/22 08:27 PM
01/05/22 08:27 PM
|
Joined: Jun 2016
Posts: 3,142 alabama northport
birdcarver
OP
10 point
|
OP
10 point
Joined: Jun 2016
Posts: 3,142
alabama northport
|
Neither use a small oven i bought at surplus store , put quarter cup powder in tupper ware bowl handfull bullets seal and shake well pour out on 1/4 '' rabbit wire ,try to spread them out with a wire to where they are not laying side by side, touching end to side is ok, cook them for 25 minutes at 400 deg, when i take them out i dump them in cold water to get the BHN around 25, with this BHN they will shoot through two tires standing end to end and keep on going. If i were going to hunt with them I would not quench them, BHN would be around 12, THIS IS WITH TIRE WTS, There is lots of sites on you tube that will show you how to get started, check out Elvis Ammo,This is how I got started, you can use the Wifes oven I want mind, ps does not make a mess
Last edited by birdcarver; 01/05/22 08:29 PM.
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: Sipseyhunter]
#3573914
01/06/22 09:48 AM
01/06/22 09:48 AM
|
Joined: Jun 2016
Posts: 3,142 alabama northport
birdcarver
OP
10 point
|
OP
10 point
Joined: Jun 2016
Posts: 3,142
alabama northport
|
I've tried the shake and bake method using harbor freight powder, but they didn't turn out as well as yours. Is the eastwood powder better to use? Never used harbor freight, bought some powder you mix alcohol and acetone make a wet mix did not care for this, so as far as I'm concerned yes I like eastwood better, once you powder coat you can hammer bullet flat on anvil and powder coat does not crack or peel off bullet therefore not leaving any lead residue in barrel of gun
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: birdcarver]
#3574020
01/06/22 11:43 AM
01/06/22 11:43 AM
|
Joined: Apr 2003
Posts: 3,304 Autaugaville
trailertrash
10 point
|
10 point
Joined: Apr 2003
Posts: 3,304
Autaugaville
|
It's my understanding that quenching the bullet only makes the surface few thousands harder, which is normally considered a good thing and it's only temporary. Seems like my reading on the subject said it would last a year or two. Just something to think about. I can't prove one way or the other.
Edit: Also remember something about if you resize after quenching that depending on how much squeezing/working of the lead you would effectively eliminate the hard shell. Again can't prove it but I dug into the subject a LOT years ago when I was casting.
Last edited by trailertrash; 01/06/22 11:45 AM.
"We aren't here to justify your feelings and give you self worth" - Aldeer Welcome Center
|
|
|
Re: powder coat 30/30 and 6.5 creedmoor
[Re: birdcarver]
#3576099
01/08/22 09:45 AM
01/08/22 09:45 AM
|
Joined: Mar 2012
Posts: 2,462 Mississippi
riflenut
10 point
|
10 point
Joined: Mar 2012
Posts: 2,462
Mississippi
|
Educate me fellas, what is the purpose of powder coating?
"The democracy will cease to exist when you take away from those who are willing to work and give to those who would not." Thomas Jefferson
"I ask, who are the militia? They consist of now of the whole people, except a few public officers." George Mason
|
|
|
|