410 roll crimping

Aldeer Classifieds

ISO boxblade
by kntree. 05/07/24 09:48 PM

WTB: 20ga remchoke
by AU7MM08. 05/07/24 05:01 PM

G Force AR style 12ga
by MikeP. 05/07/24 02:29 PM

Winchester sx4 20 ga $900
by CrappieMan. 05/07/24 02:22 PM

WTB 3” Remington 870 20 gauge
by JUGHEAD. 05/07/24 10:55 AM

Serious Deer Talk

For the Don’t Shoot Does Crowd
by Mbrock. 05/07/24 10:17 PM

Kansas Bowhunt timing
by ColeT. 05/07/24 02:57 PM

Meat hunt outfitter?
by Snuffy. 05/06/24 03:28 PM

Land, Leases, Hunting Clubs

Lowndes county club
by Doeslayer44. 05/07/24 10:11 AM

Looking for Turkey Hunting Land
by Nightwatchman. 05/06/24 01:46 PM

Need dozer work. Cullman area
by Trecker1. 05/02/24 02:33 PM

Hunting Lease Insurance
by mw2015. 04/23/24 07:49 PM

7 registered members (Tree Dweller, Captain Howdy, mauvilla, Longtine, FastXD, Morris, auman), 784 guests, and 0 spiders.

Key: Admin, Global Mod, Mod

Print Thread

410 roll crimping #3052922 02/26/20 02:15 PM 02/26/20 02:15 PM
Joined: Jan 2014 Posts: 7,926 sj22 OP 14 point
sj22 OP 14 point Joined: Jan 2014 Posts: 7,926	Is there some trick I haven’t figured out or is it impossible to get the crimp as pretty as the ones on my 20 gauge loads? I loaded some and just can’t get them to look perfect. I sent Hal some pictures of it and he said it was fine but was just wondering if anyone else can get them as good as the 20 gauge?

Re: 410 roll crimping [Re: sj22] #3052953 02/26/20 02:50 PM 02/26/20 02:50 PM
Joined: Oct 2012 Posts: 10,628 Central, Al Bustinbeards Booner
Bustinbeards Booner Joined: Oct 2012 Posts: 10,628 Central, Al	Those small hulls are just tough to get a good crimp on. Just go slow and let the crimp bit get real warm. Originally Posted By: Wiley Coyote Well, the way I see it is there's just too many assholes On a good day there's a bunch of assholes in here. On a bad day there's too many assholes in here.

Re: 410 roll crimping [Re: sj22] #3052959 02/26/20 02:56 PM 02/26/20 02:56 PM
Joined: Nov 2011 Posts: 1,044 NC hawglips 6 point
hawglips 6 point Joined: Nov 2011 Posts: 1,044 NC	1) Go EASY on the downward pressure, and then let up a bit more.... 2) A swab of WD40 around the upper outside edge of the hull is a very nice touch to improve aesthetics 3) use a Precision or GAEP crimp die....

Re: 410 roll crimping [Re: sj22] #3053017 02/26/20 04:37 PM 02/26/20 04:37 PM
Joined: Mar 2016 Posts: 3,622 Spanish Fort TurkeyJoe 10 point
TurkeyJoe 10 point Joined: Mar 2016 Posts: 3,622 Spanish Fort	Are you trimming any hull off Shaun? Reckon you’re folding too much over? Micah 6:8

Re: 410 roll crimping [Re: sj22] #3053022 02/26/20 04:41 PM 02/26/20 04:41 PM
Joined: Apr 2015 Posts: 7,832 North Alabama Hevishot13 14 point
Hevishot13 14 point Joined: Apr 2015 Posts: 7,832 North Alabama	Use a gaep crimper. I had the same problem until I switched to a gaep. Now they look better than factory

Re: 410 roll crimping [Re: TurkeyJoe] #3053061 02/26/20 06:11 PM 02/26/20 06:11 PM
Joined: Jan 2014 Posts: 7,926 sj22 OP 14 point
sj22 OP 14 point Joined: Jan 2014 Posts: 7,926	Originally Posted by TurkeyJoe Are you trimming any hull off Shaun? Reckon you’re folding too much over? I need to try that, it is a lot more to crimp than the 20 gauge