|
|
|
|
|
|
|
1
|
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
|
30
|
|
|
|
|
|
|
|
|
109 registered members (m97, Birdman83, Happysappy, cdaddy14, quailman, donia, Scout308, Bmyers142, claybird, geeb1, WC82, Turkey, Dekalb123, dustymac, Deerslayer33, BC_Reb, CNC, Catbird, CrappieMan, jawbone, BCLC, sw1002, jellyhead11, lectrode, Pwyse, coachg34, Ten37, BobK, cullbuck, BamaFan64, FreeStateHunter, Fedex 1, odocoileus, Ridge Life, bowkl, AU coonhunter, dave260rem!, SEWoodsWhitetail, Snuffy, desertdog, Ol’Tom, courseup, Young20, Downwind, CatHeadBiscuit, Overland, Gut Pile 32, bug54, Joe4majors, robinhedd, timberwolfe, DoubleShoalsJR, kyles, Narrow Gap, GomerPyle, Drycreek, jwalker77, MarksOutdoors, Teacher One, ts1979flh, AU338MAG, woodduck, bambam32, Jason Carroll, sawdust, Red Fox, Big AL 76, BamaGuitarDude, oldknight, globe, Skullworks, Turberville, Tree Dweller, Whiskey9, top cat, Jstocks, 4Him146, coosabuckhunter, Whild_Bill, Justice, gbee, FNG68, mopar, mcninja, sj22, timberman56, hoggin, fur_n_feathers, IDOT, Mike59, Geezer, Aldecks1, Mbrock, seapro19, furnfeather, Swamp Monkey, dtmwtp, bamabeagler, 11 invisible),
605
guests, and 0
spiders. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
Re: Appliance part needed
[Re: lobuc]
#3676781
05/24/22 06:05 PM
05/24/22 06:05 PM
|
Joined: Jan 2014
Posts: 1,192
North of Lake Martin area
Frogeye
OP
6 point
|
OP
6 point
Joined: Jan 2014
Posts: 1,192
North of Lake Martin area
|
I see some suggestions of using a universal or one from another manufacturer good ideas but impossible to find the specific specs. This part is a potentiometer not a simple make or break switch. Without knowing the values at each detent position, placement of the harness plug/contact relation and finally mounting and clocking it for the specific application makes it difficult to narrow down. I just ordered a 5304500591, it supposedly has the same 8 positions and a 4 contact harness connector (mine only uses 3 of them). Need to use a die to cut threads in lower part where shaft meets body hoping that is the extent of modifications needed. I guess I'm the guinea pig. Let me know how it goes. I may go ahead and order one myself now. I guess your oven is the same model, 790.79523600? The knob is large enough to hide them, you could just drill 2 holes through the panel and use screws to mount it. At least it looks like that after a quick view.
Last edited by Frogeye; 05/24/22 06:06 PM. Reason: Correct spelling
|
|
|
|
