|
|
1
|
2
|
3
|
4
|
5
|
6
|
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
|
28
|
29
|
30
|
|
|
|
|
|
|
Cylinder Release Problem
#3182131
08/02/20 11:34 AM
08/02/20 11:34 AM
|
Joined: Aug 2001
Posts: 3,971
Gardendale AL
Stripe
OP
10 point
|
OP
10 point
Joined: Aug 2001
Posts: 3,971
Gardendale AL
|
Not working on my charter arms 38 spl revolver. Is it adjustable? Thanks
Striper Steve;
"Aim Small, Hit Small"
|
|
|
Re: Cylinder Release Problem
[Re: Stripe]
#3182147
08/02/20 11:52 AM
08/02/20 11:52 AM
|
Joined: Jan 2003
Posts: 12,681
behind my Dillon
dave260rem!
Skinny’s Ex
|
Skinny’s Ex
Joined: Jan 2003
Posts: 12,681
behind my Dillon
|
Holy crap a Stripe sighting!
Make sure the screw is tightend down. Otherwise take it to Gundoc he's good people.
Only hits count.
|
|
|
Re: Cylinder Release Problem
[Re: Stripe]
#3182190
08/02/20 12:38 PM
08/02/20 12:38 PM
|
Joined: Jun 2013
Posts: 52,164
Gee's Bend/At The Hog Pen
James
Freak of Nature
|
Freak of Nature
Joined: Jun 2013
Posts: 52,164
Gee's Bend/At The Hog Pen
|
Holy crap a Stripe sighting!
Make sure the screw is tightend down. Otherwise take it to Gundoc he's good people. Make sure the cylinder rod is tight also. Yeah check both. Especially the cylinder rod, i bet it's catching
How many people am i willing to sacrifice for freedom?
Everyone. All of them...
Do not regret growing older, it's a privilege denied to many!
|
|
|
Re: Cylinder Release Problem
[Re: Stripe]
#3182223
08/02/20 01:09 PM
08/02/20 01:09 PM
|
Joined: Oct 2008
Posts: 8,142
In front of my lathe
gundoc
14 point
|
14 point
Joined: Oct 2008
Posts: 8,142
In front of my lathe
|
A Charter Arms has a few things that can cause that problem.
As mention above, check the collar on the ejector rod and the screw that holds the thumb latch on.
Some version of those guns have an adjustable, pin inside the frame.
I have seen those turn themselves in with use and cause a sticking problem.
You can turn it back out with a small flat tip screwdriver.
If that's the case, I'd put some blue loc tite on it before calling it good.
There are two types of gun enthusiasts ... Those who have been F#CKED by PTG and those who will be!
~ unknown
|
|
|
Re: Cylinder Release Problem
[Re: Stripe]
#3182628
08/03/20 06:42 AM
08/03/20 06:42 AM
|
Joined: Aug 2001
Posts: 3,971
Gardendale AL
Stripe
OP
10 point
|
OP
10 point
Joined: Aug 2001
Posts: 3,971
Gardendale AL
|
There is a latch assembly screw below the firing pin. I adjusted it out a little and it helped. Will keep messing with it.
Thank for the help
Striper Steve;
"Aim Small, Hit Small"
|
|
|
Re: Cylinder Release Problem
[Re: Stripe]
#3182637
08/03/20 07:07 AM
08/03/20 07:07 AM
|
Joined: Oct 2008
Posts: 8,142
In front of my lathe
gundoc
14 point
|
14 point
Joined: Oct 2008
Posts: 8,142
In front of my lathe
|
Yeah that's the adjustable pin I was referring to.
There are two types of gun enthusiasts ... Those who have been F#CKED by PTG and those who will be!
~ unknown
|
|
|
|
